TransmutationsDeBase : Différence entre versions

De fablabo
Aller à : navigation, rechercher
(code source)
m
 
(10 révisions intermédiaires par 2 utilisateurs non affichées)
Ligne 1 : Ligne 1 :
 
{{Projet
 
{{Projet
 
|status=Prototype
 
|status=Prototype
 +
|status_pub=Publié
 
|image=20160426 183856.jpg
 
|image=20160426 183856.jpg
 
|description=tableau électrique télécommandé pour performance phytoaquatique
 
|description=tableau électrique télécommandé pour performance phytoaquatique
Ligne 59 : Ligne 60 :
  
 
== code source ==
 
== code source ==
<code language='arduino'>
 
  
 +
<code  lang='C++' linenumbers>
 
class Cooker
 
class Cooker
 
{
 
{
Ligne 275 : Ligne 276 :
 
digitalWrite(ledPin, LOW);
 
digitalWrite(ledPin, LOW);
 
}
 
}
 
 
 
 
 
</code>
 
</code>

Version actuelle en date du 8 juin 2021 à 14:51


tableau électrique télécommandé pour performance phytoaquatique

20160426 183856.jpg

Contributeur·ice·s

Statut du projet

Prototype

Statut de la publication

Publié

License

GFDL

Inspiration

Fichiers source

Découpe laser capot transmutations.svg

Machines

Matériaux




introduction

Pour une performance faisant appel à des chauffe-ballons sans thermostat et des pompes d'aquarium, j'ai conçu un système permettant d'une part de mettre les personnes en sécurité (utilisation d'appareils électriques dans un environnement encombré par des aquariums et des ballons), d'autre part de commander par radio des relais permettant de maintenir les chauffe-ballons à température constante, les éteindre, les mettre en marche forcée.

BOM

boîtier

  • contreplaqué de bouleau qualité extérieure 9mm de chez Leroy-Merluche (Dispano vend des plaques trop grandes pour passer dans le fourgon)
  • * Adaptateur USB A vers B chassis conradpro 1214673 - 62

électricité de puissance

  • 6 prises de courant femelle Legrand gamme Mosaic
  • 2 plaques 4 modules + support Legrand gamme Mosaic
  • un disjoncteur différentiel type A 40A 30mA
  • un disjoncteur 16A
  • un disjoncteur 10A
  • 3 Bornier 8 connexions P+N+T
  • Rail DIN de connexion (pris dans un boîtier Legrand 1er prix par ce que ces couillons ne les distribuent pas seuls)

électronique

  • 1 Arduino Uno
  • 6 module relais 250V 7A Tinker it chez snootlab TK-00012
  • 1 Télécommande keyfob 315mhz DFROBOT FIT0355
  • 1 shield télécommande RF 315Mhz DFROBOT TEL0075
  • 1 shield à visser DFROBOT DFR0060
  • câble USB A vers B 25cm e44
  • 6 câble tinker kit 20cm
  • transfo USB 5V 1A + câble hacké vers un adaptateur

A la réflexion, il manque un presse-étoupe pour le câble d'alim. La poignée semble inutile.

plans

Découpe laser capot transmutations.svg fichier SVG de la découpe laser du capot. Il faut corriger : élargir de 2.5mm à droite les deux découpes du bas.

Transmut planche debit mars2016.svg Plan de débit & dessin de la face et du haut du boîtier.

Transmut arriere mars2016.svg Plan du panneau arrière de la boite.

Transmut facade mars2016.svg Plan de la face avant.

fichier fritzing du montage Arduino à venir

code source

class Cooker { byte relaisPin; unsigned long decalage; unsigned long intervalle;

byte relaisEtat; byte cookingEtat; unsigned long prevMillis;

public: Cooker(byte pin, unsigned long offset, unsigned long interval) { relaisPin = pin; pinMode(relaisPin, OUTPUT);

decalage = offset; intervalle = interval; relaisEtat = LOW; cookingEtat = 0; prevMillis = 0; }

void epochUpdate() { prevMillis = millis(); }

void Update() { unsigned long currMillis = millis();

if ((cookingEtat == 0) && (relaisEtat == LOW) && (currMillis - prevMillis <= decalage)) { relaisEtat = HIGH; digitalWrite(relaisPin, relaisEtat); Serial.print(int(currMillis / 1000)); Serial.print(" ColdStart relay "); Serial.println(relaisPin); Serial.println(" to "); Serial.println(relaisEtat); } else if ((cookingEtat == 0) && (currMillis - prevMillis >= decalage)) { cookingEtat = 1; }


if ((cookingEtat) && (relaisEtat == LOW) && (currMillis - prevMillis <= intervalle)) { relaisEtat = HIGH; digitalWrite(relaisPin, relaisEtat); Serial.print(int(currMillis / 1000)); Serial.print(" Cooking relay "); Serial.println(relaisPin); Serial.println(" to "); Serial.println(relaisEtat); } else if ((cookingEtat) && (relaisEtat == HIGH) && (currMillis - prevMillis >= intervalle)) { relaisEtat = LOW; digitalWrite(relaisPin, relaisEtat); Serial.print(int(currMillis / 1000)); Serial.print(" Cooking relay "); Serial.println(relaisPin); Serial.println(" to "); Serial.println(relaisEtat); } else if ((cookingEtat) && (currMillis - prevMillis >= 10000)) { prevMillis = currMillis; Serial.print("RAZ Cooking relay "); Serial.println(relaisPin); } } void Stop() { if (relaisEtat == HIGH) { relaisEtat = LOW; } }

void Full() { if (relaisEtat == LOW) { relaisEtat = HIGH; } } }; // constants attribution des pins // 2, 3, 4, 5, 14, 19

// constantes decalage des cb avant de passer etat 2 = // 9000; 11400; 12000; 12600; // // Intervalle de chauffe durant l'etat 2 = // 1500; 1900; 2200; 3000; //

unsigned int globalState ; unsigned int prevGlobalState = 0;

unsigned long epoch = 0;

// on instancie

Cooker relais0(2, 9000, 1500); Cooker relais1(3, 11400, 1900); Cooker relais2(4, 12000, 2200); Cooker relais3(5, 12600, 3000); Cooker relais4(14, 8000, 2200); Cooker relais5(19, 14000, 3500);


//////////////////////////////////////////////// /////////////// telecommande RF /////////////// ////////////////////////////////////////////////

/*The following 4 pin definitions,correspond to 4 buttons on the remote control

 //(The telecontroller is Remote Wireless Keynob 315MHz(SKU:FIT0355))*/

const unsigned int D1 = 8; //The digital output pin 1 of decoder chip(SC2272) const unsigned int D2 = 9; //The digital output pin 2 of decoder chip(SC2272) const unsigned int D3 = 10; //The digital output pin 3 of decoder chip(SC2272) const unsigned int D4 = 11; //The digital output pin 4 of decoder chip(SC2272) const unsigned int ledPin = 13; //Receiving indicator

volatile int stateRF = LOW;

void setup() { Serial.begin(9600); epoch = millis(); // pour stocker le chrono depuis le démarrage //========== RF ======================= pinMode(D4, INPUT); //Initialized to input pin, in order to read the level of //the output pins from the decoding chip pinMode(D2, INPUT); pinMode(D1, INPUT); pinMode(D3, INPUT); pinMode(ledPin, OUTPUT); attachInterrupt(1, blink, RISING); //Digital pin 3,interrupt 1,corresponds to //receiving interrupt pin of the decoding chip digitalWrite(ledPin, LOW); }

void loop() {

ecouteRadio(); // la commande RF actualise l'etat global

if ((globalState == 1) || (globalState == 2)) { relais0.Update(); relais1.Update(); relais2.Update(); relais3.Update(); relais4.Update(); relais5.Update(); } else if (globalState == 0) { relais0.Stop(); relais1.Stop(); relais2.Stop(); relais3.Stop(); relais4.Stop(); relais5.Stop(); } else if (globalState == 3) { relais0.Full(); relais1.Full(); relais2.Full(); relais3.Full(); relais4.Full(); relais5.Full(); } } /////////////// les fonctions //////////////////////


void blink() { stateRF = ! stateRF; } ////////////////////////////////// void ecouteRadio() { delay(1); digitalWrite(ledPin, HIGH); // Serial.print("Locked "); // Read individually output pins of the decoder chip, if ((digitalRead(D4) == 1) && (globalState != 0)) // locked icon == stop { globalState = 0; Serial.println("Locked = STOP"); } if (digitalRead(D2) == 1 && globalState != 1) // unlocked icon == cold start { globalState = 1; epoch = millis(); Serial.println("Unlocked : Cold Start"); } if (digitalRead(D1) == 1 && globalState != 2) // blitz icon == cooking { globalState = 2; Serial.println("Blitz : Cooking"); } if (digitalRead(D3) == 1 && globalState != 3) // alarm icon == full throttle { globalState = 3; Serial.println("Alarm : FULL"); } digitalWrite(ledPin, LOW); }